Öz
In this study, affect of aging on wear characteristics of the nano GNP reinforced Al6061 metal matrix composites. In this scope, the samples were produced by hot press at 500 ℃ temperature under 50 MPa pressure for 30 minutes. The wear characteristics of the composites were determined using the ball-on disc wear test method. The affect of aging on the friction coefficient and wear ratio were investigated. Graphene reinforcement significantly increased the friction coefficient between the stainless steel ball and specimen but aging process lowered the coefficient of friction to a better level. Also artificially aged specimens showed significant increase in hardness values. Key factors are affecting the mechanical performance of the Al based alloy is reinforcement and aging process.
Anahtar Kelimeler
Powder Metallurgy Metal Matrix Composites Aging Wear Properties
Kaynakça
- [1] N. Akçamlı, B. Şenyurt, H. Gökçe, and D. Ağaoğulları, Powder metallurgical fabrication of graphene reinforced near-eutectic Al-Si matrix composites: Microstructural, mechanical and electrochemical characterization, Eng. Sci. Technol. an Int. J. (2021).
- [2] N. Kumar, A. Bharti, and K. K. Saxena, A re-investigation: Effect of powder metallurgy parameters on the physical and mechanical properties of aluminium matrix composites, Mater. Today Proc., vol. 44 (2021) pp. 2188–2193.
- [3] N. R. Rathod and J. V. Menghani, Influence of precipitation hardening in aluminum based systems: A literature review, AIP Conf. Proc., vol. 2317, no. February, (2021), 020035/1-11.
- [4] S. Pal, R. Mitra, and V. V. Bhanuprasad, Aging behaviour of Al-Cu-Mg alloy-SiC composites, Mater. Sci. Eng. A, vol. 480, no. 1–2 (2008) pp. 496–505.
- [5] S. Mozammil, J. Karloopia, R. Verma, and P. K. Jha, Effect of varying TiB2 reinforcement and its ageing behaviour on tensile and hardness properties of in-situ Al-4.5%Cu-xTiB2 composite, J. Alloys Compd., vol. 793 (2019) pp. 454–466.
- [6] T. Han, F. Wang, J. Li, C. He, and N. Zhao, Effect of GNPs on microstructures and mechanical properties of GNPs/Al-Cu composites with different heat treatment status, J. Mater. Sci. Technol., vol. 92 (2021) pp. 1–10.
Öz
Kaynakça
- [1] N. Akçamlı, B. Şenyurt, H. Gökçe, and D. Ağaoğulları, Powder metallurgical fabrication of graphene reinforced near-eutectic Al-Si matrix composites: Microstructural, mechanical and electrochemical characterization, Eng. Sci. Technol. an Int. J. (2021).
- [2] N. Kumar, A. Bharti, and K. K. Saxena, A re-investigation: Effect of powder metallurgy parameters on the physical and mechanical properties of aluminium matrix composites, Mater. Today Proc., vol. 44 (2021) pp. 2188–2193.
- [3] N. R. Rathod and J. V. Menghani, Influence of precipitation hardening in aluminum based systems: A literature review, AIP Conf. Proc., vol. 2317, no. February, (2021), 020035/1-11.
- [4] S. Pal, R. Mitra, and V. V. Bhanuprasad, Aging behaviour of Al-Cu-Mg alloy-SiC composites, Mater. Sci. Eng. A, vol. 480, no. 1–2 (2008) pp. 496–505.
- [5] S. Mozammil, J. Karloopia, R. Verma, and P. K. Jha, Effect of varying TiB2 reinforcement and its ageing behaviour on tensile and hardness properties of in-situ Al-4.5%Cu-xTiB2 composite, J. Alloys Compd., vol. 793 (2019) pp. 454–466.
- [6] T. Han, F. Wang, J. Li, C. He, and N. Zhao, Effect of GNPs on microstructures and mechanical properties of GNPs/Al-Cu composites with different heat treatment status, J. Mater. Sci. Technol., vol. 92 (2021) pp. 1–10.
Ayrıntılar
| Birincil Dil | İngilizce |
|---|---|
| Konular | Mühendislik |
| Bölüm | Research Article |
| Yazarlar | |
| Erken Görünüm Tarihi | 1 Eylül 2022 |
| Yayımlanma Tarihi | 1 Ağustos 2022 |
| Kabul Tarihi | 17 Mart 2022 |
| Yayımlandığı Sayı | Yıl 2022 Cilt: 50 Sayı: 3 |
Kaynak Göster
HACETTEPE JOURNAL OF BIOLOGY AND CHEMİSTRY
Copyright © Hacettepe University Faculty of Science